Error code 62 – Wait for stop signal

Have you just updated the firmware of the machine?

Does restarting the machine and dentalcnc solve the issue?

How to check this:

1. Close dentalcnc.
2. Switch off the machine at the main power switch.
3. Wait 10 seconds.
4. Switch on the machine at the main power switch.
5. Start dentalcnc.
• The machine references.

Did the machine (axes and blank changer if available) successfully reference?

Yes
The axes didn’t reference The blank changer Machine component which stores multiple blanks in a magazine and which can automatically load them into the working chamber.. When using the search, use a blank changer or a blank magazine instead didn’t reference

S2 / S5: Is the blank changer in the default position?

How to check this:

1. Open the working chamber door.
2. Check if the blank changer Machine component which stores multiple blanks in a magazine and which can automatically load them into the working chamber.. When using the search, use a blank changer or a blank magazine instead flap (marked orange) is fully closed.

Fully closed blank changer Machine component which stores multiple blanks in a magazine and which can automatically load them into the working chamber.. When using the search, use a blank changer or a blank magazine instead flap (marked orange)

In the following figure, the blank changer Machine component which stores multiple blanks in a magazine and which can automatically load them into the working chamber.. When using the search, use a blank changer or a blank magazine instead flap (marked orange) is open and the blank changer Machine component which stores multiple blanks in a magazine and which can automatically load them into the working chamber.. When using the search, use a blank changer or a blank magazine instead carriage (marked green) has moved into the working chamber. In this case, the blank changer Machine component which stores multiple blanks in a magazine and which can automatically load them into the working chamber.. When using the search, use a blank changer or a blank magazine instead is not in default position.

Open blank changer Machine component which stores multiple blanks in a magazine and which can automatically load them into the working chamber.. When using the search, use a blank changer or a blank magazine instead flap (marked orange); blank changer Machine component which stores multiple blanks in a magazine and which can automatically load them into the working chamber.. When using the search, use a blank changer or a blank magazine instead carriage (marked green) is in working chamber

Does dentalcnc indicate that the blank changer is in default position?

1. Start dentalcnc.
2. Open the dentalcnc Application settings. For this, select the following icon in the main icon bar: 
3. Open the Machine maintenance view. For this, select the following icon in the lower icon bar: 
4. Check if the upper icon labeled 10 in the DG column is highlighted.
5. Verify that the upper icon labeled 10 in the DZ column is highlighted.

Icons that must be highlighted (marked orange)

Is the blank magazine in the default position?

How to check this:

1. Open the Machining view. For this, select the following icon in the main icon bar: 
2. Verify that the following icon (marked orange) is highlighted:

Icon which needs to be highlighted (marked orange)

Recommendation

It may have been a temporary issue.

• Restart the job.

Recommendation

It may have been a temporary issue.

• Restart the job.

Recommendation

1. Manually reset the blank changer Machine component which stores multiple blanks in a magazine and which can automatically load them into the working chamber.. When using the search, use a blank changer or a blank magazine instead to default position.  Starting, interrupting, canceling jobs
2. Test the blank changer Machine component which stores multiple blanks in a magazine and which can automatically load them into the working chamber.. When using the search, use a blank changer or a blank magazine instead:
1. Mount blanks of different materials to all blank magazine Part of the blank changer in which you store the blanks for automatic loading. slots.
• If the following applies, the blank changer Machine component which stores multiple blanks in a magazine and which can automatically load them into the working chamber.. When using the search, use a blank changer or a blank magazine instead test is successful:
1. All blanks were successfully loaded and unloaded.
2. The gripper and swivel axis moved steadily and smoothly.
3. The blank changer Machine component which stores multiple blanks in a magazine and which can automatically load them into the working chamber.. When using the search, use a blank changer or a blank magazine instead carriage and blank changer Machine component which stores multiple blanks in a magazine and which can automatically load them into the working chamber.. When using the search, use a blank changer or a blank magazine instead flap moved steadily and smoothly.
3. If the blank magazine Part of the blank changer in which you store the blanks for automatic loading. test was not successful: Contact customer service.

Recommendation

There may be a problem with the end switches of the blank changer Machine component which stores multiple blanks in a magazine and which can automatically load them into the working chamber.. When using the search, use a blank changer or a blank magazine instead.

• Contact customer service.

Recommendation

The proximity switch which detects the position of the blank magazine Part of the blank changer in which you store the blanks for automatic loading. may need repair.

Recommendation

• Contact customer service.